阻焊层是绿油吗:如何在路由器上安装ios

来源:百度文库 编辑:高校问答 时间:2024/03/29 04:00:46
怎么用TFTP在路由器上安装IOS,说的细一些,我要全过程。。。谢谢了。。

你的是不是cisco的路由器?
我贴一篇cisco的步骤你看看:
Cisco路由器IOS映像恢复及升级方法
由于历史原因,Cisco公司的路由器产品丰富且繁杂,Cisco路由器的专用操作系统IOS映像也同时存在多个版本,以下就分别针对两类加载不同版本的IOS映像文件的Cisco路由器做讨论。
一、Cisco 1000,1600,2500,4000系列
1、IOS映像恢复的方法及步骤
1) 连接PC的COM1口与路由器的console口,使用PC的超级终端软件访问该路由器;
2) 开启路由器的电源开关,并在30秒内按下键盘的Ctrl+break,中断路由器的正常启动以进入rom监视模式,屏幕上提示符如下:
>
3) 键入如下命令:
>o /r 0x2101
改变路由器虚拟寄存器的默认值(0x2102);
4) 键入重启命令:
>i
路由器重启,当屏幕显示以下信息表明路由器重启完毕:
System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
Copyright (c) 1986-1995 by cisco Systems
2500 processor with 1024 Kbytes of main memory

Press RETURN to get started!
5) 路由器在虚拟寄存器的值为0x2101时自动进入rom启动模式:
router(boot)>
6) 此时,将TFTP服务器上的IOS映像文件恢复至路由器flash memory中,依次键入以下命令:
router(boot)>en
router(boot)#copy tftp flash
System flash directory:
No files in System flash
[0 bytes used, 4194304 available, 4194304 total]
Address or name of remote host [255.255.255.255]?192.168.18.168(IP地址已作技术处理,下同)
Source file name? igs-i-l.110-22a.bin(IOS映像文件名)
Destination file name [igs-i-l.110-22a.bin]?
Accessing file 'igs-i-l.110-22a.bin' on 192.168.18.168...
Loading igs-i-l.110-22a.bin from 192.168.18.168 (via Ethernet0): ! [OK]
Device needs erasure before copying new file
Erase flash device before writing? [confirm]
Copy 'igs-i-l.110-22a.bin' from server
as 'igs-i-l.110-22a.bin' into Flash WITH erase? [yes/no]y
Erasing device... eeeeeeeeeeeeeeee ...erased
Loading igs-i-l.110-22a.bin from 192.168.18.168 (via Ethernet0): !!!!!!!!!!!!!!!!!!!!(!表示恢复成功)
7) 还原路由器虚拟寄存器的默认值(0x2102),恢复路由器的正常启动顺序,依次键入以下命令:
router(boot)#conf t
router(boot)(config)#config-register 0x2102
router(boot)(config)#exit
router(boot)#wr
router(boot)#reload
2、IOS映像升级的方法及步骤
1) 升级之前先备份,将相关文件备份至TFTP服务器,键入如下命令:
router#copy bootflash tftp(Cisco 2500系列路由器不存在bootflash,相应的是rom)
router#copy flash tftp
router#copy startup-config tftp
2) 因为Cisco 1000,1600,2500,4000系列路由器不允许在正常工作状态下重写flash memory,所以只有进入rom(或bootflash)启动模式才能升级IOS映像,依次键入以下命令:
router#conf t
router(config)#config-register 0x2101
router(config)#exit
router#wr
router#reload
3) 路由器重启完毕后进入rom(或bootflash)启动模式,从TFTP服务器将新的IOS映像文件拷贝至路由器的flash memory中:
router(boot)#copy tftp flash
4) 还原路由器虚拟寄存器的默认值(0x2102),恢复路由器的正常启动顺序,依次键入以下命令:
router(boot)#conf t
router(boot)(config)#config-register 0x2102
router(boot)(config)#exit
router(boot)#wr
router(boot)#reload
二、Cisco 1700,2600,3600,7200系列
1、IOS映像恢复的方法及步骤
1) 连接PC的COM1口与路由器的console口,使用PC的超级终端软件访问该路由器;
2) 开启路由器的电源开关,并在30秒内按下键盘的Ctrl+break,中断路由器的正常启动以进入rom监视模式,屏幕上提示符如下:
rommon 1>
3) 键入xmodem命令:
rommon 1>xmodem c3640-i-mz.120-10.bin(IOS映像文件名)
4) 然后,路由器一直等待从PC上接收该IOS映像文件,此时在超级终端软件中点击发送选项,选择存放在PC本地硬盘中的IOS映像文件,确定后即开始下载文件至路由器的flash memory中,由于通讯带宽只有9600波特,整个文件下载时间约为1.5小时(依文件大小而定),屏幕显示信息如下:
Do not start the sending program yet...
device does not contain a valid magic number
dir: cannot open device flash:
WARNING: All existing data in flash will be lost!
Invoke this application only for disaster recovery.
Do you wish to continue? y/n[n]:y
Ready to receive file c3640-i-mz.120-10.bin ...
Erasing flash at 0x307c0000
program flash location 0x30380000
Download Complete!
program load complete, entry point: 0x80008000, size: 0x38f410
5) 接着,路由器将自动重启,屏幕显示信息如下:
Self decompressing the image : ################################# [OK]

Press RETURN to get started!
2、IOS映像升级的方法及步骤
1) 同理,升级之前先备份,将关键文件备份至TFTP服务器,键入下列命令: router#copy bootflash tftp(Cisco 3600系列路由器不存在bootflash)
router#copy flash tftp
router#copy startup-config tftp
2) 因为Cisco 1700,2600,3600,7200系列路由器允许在正常工作状态下重写flash memory,所以直接键入以下命令就可完成IOS映像的在线升级:
router#copy tftp flash
router#reload
或者,为保险起见(以路由器停止服务为代价),在进入rom监视模式后才进行IOS映像的升级,则依次进行下列操作:
2) 在路由器重启加电后30秒内按下键盘的Ctrl+break,中断路由器的正常启动直接进入rom监视模式,屏幕上提示符如下:
rommon 1>
或者,在路由器重启过程完成后进行以下操作,同样可以进入路由器的rom监视模式:
router#conf t
router(config)#config-register 0x0
router(config)#exit
router#wr
router#reload
rommon 1>
3) 键入以下命令,将IOS映像的升级文件从TFTP服务器复制至路由器的flash memory中:
rommon 1>b c3640-i-mz.121-2.T 192.168.18.168
program load complete, entry point: 0x80008000, size: 0x4ed478
Self decompressing the image : ##################################[OK]
Loading c3640-i-mz.121-2.T from 192.168.18.168 (via Ethernet0/0):!!!!!!!!!!!!!!!
[OK - 5166484/10332160 bytes]
4) 还原路由器虚拟寄存器的默认值(0x2102),恢复路由器的正常启动顺序,依次键入以下命令:
rommon 1>confreg 0x2102
5) 键入重启命令,使得新配置生效,完成IOS映像的离线升级:
rommon 2>reset