2007年生产的金沱牌3年:盟军敢死队4的安装问题

那也许是因为你的系统中的两个DOS文件被删除的原因，游戏不能自解压。两个文件应该分别是AUTOEXEC.NT和CONFIG.NT。具体的编辑方法是建立个新的记事本。输入
　　@echo off

　　REM AUTOEXEC.BAT is not used to initialize the MS-DOS environment.
　　REM AUTOEXEC.NT is used to initialize the MS-DOS environment unless a
　　REM different startup file is specified in an application's PIF.

　　REM Install CD ROM extensions
　　lh %SystemRoot%\system32\mscdexnt.exe

　　REM Install network redirector (load before dosx.exe)
　　lh %SystemRoot%\system32\redir

　　REM Install DPMI support
　　lh %SystemRoot%\system32\dosx

　　REM The following line enables Sound Blaster 2.0 support on NTVDM.
　　REM The command for setting the BLASTER environment is as follows:
　　REM SET BLASTER=A220 I5 D1 P330
　　REM where:
　　REM A specifies the sound blaster's base I/O port
　　REM I specifies the interrupt request line
　　REM D specifies the 8-bit DMA channel
　　REM P specifies the MPU-401 base I/O port
　　REM T specifies the type of sound blaster card
　　REM 1 - Sound Blaster 1.5
　　REM 2 - Sound Blaster Pro I
　　REM 3 - Sound Blaster 2.0
　　REM 4 - Sound Blaster Pro II
　　REM 6 - SOund Blaster 16/AWE 32/32/64
　　REM
　　REM The default value is A220 I5 D1 T3 and P330. If any of the switches is
　　REM left unspecified, the default value will be used. (NOTE, since all the
　　REM ports are virtualized, the information provided here does not have to
　　REM match the real hardware setting.) NTVDM supports Sound Blaster 2.0
　　only.
　　REM The T switch must be set to 3, if specified.
　　SET BLASTER=A220 I5 D1 P330 T3

　　REM To disable the sound blaster 2.0 support on NTVDM, specify an invalid
　　REM SB base I/O port address. For example:
　　REM SET BLASTER=A0

　　保存后缀名为NT的AUTOEXEC文件。

　　CONFIG.NT的编辑方式也差不多，保存后缀名.NT的CONFIG文件

　　REM Windows MS-DOS Startup File
　　REM
　　REM CONFIG.SYS vs CONFIG.NT
　　REM CONFIG.SYS is not used to initialize the MS-DOS environment.
　　REM CONFIG.NT is used to initialize the MS-DOS environment unless a
　　REM different startup file is specified in an application's PIF.
　　REM
　　REM ECHOCONFIG
　　REM By default, no information is displayed when the MS-DOS environment
　　REM is initialized. To display CONFIG.NT/AUTOEXEC.NT information, add
　　REM the command echoconfig to CONFIG.NT or other startup file.
　　REM
　　REM NTCMDPROMPT
　　REM When you return to the command prompt from a TSR or while running an
　　REM MS-DOS-based application, Windows runs COMMAND.COM. This allows the
　　REM TSR to remain active. To run CMD.EXE, the Windows command prompt,
　　REM rather than COMMAND.COM, add the command ntcmdprompt to CONFIG.NT or
　　REM other startup file.
　　REM
　　REM DOSONLY
　　REM By default, you can start any type of application when running
　　REM COMMAND.COM. If you start an application other than an MS-DOS-based
　　REM application, any running TSR may be disrupted. To ensure that only
　　REM MS-DOS-based applications can be started, add the command dosonly to
　　REM CONFIG.NT or other startup file.
　　REM
　　REM EMM
　　REM You can use EMM command line to configure EMM(Expanded Memory Manager).
　　REM The syntax is:
　　REM
　　REM EMM = [A=AltRegSets] [B=BaseSegment] [RAM]
　　REM
　　REM AltRegSets
　　REM specifies the total Alternative Mapping Register Sets you
　　REM want the system to support. 1 <= AltRegSets <= 255. The
　　REM default value is 8.
　　REM BaseSegment
　　REM specifies the starting segment address in the Dos conventional
　　REM memory you want the system to allocate for EMM page frames.
　　REM The value must be given in Hexdecimal.
　　REM 0x1000 <= BaseSegment <= 0x4000. The value is rounded down to
　　REM 16KB boundary. The default value is 0x4000
　　REM RAM
　　REM specifies that the system should only allocate 64Kb address
　　REM space from the Upper Memory Block(UMB) area for EMM page frames
　　REM and leave the rests(if available) to be used by DOS to support
　　REM loadhigh and devicehigh commands. The system, by default, would
　　REM allocate all possible and available UMB for page frames.
　　REM
　　REM The EMM size is determined by pif file(either the one associated
　　REM with your application or _default.pif). If the size from PIF file
　　REM is zero, EMM will be disabled and the EMM line will be ignored.
　　REM
　　dos=high, umb
　　device=%SystemRoot%\system32\himem.sys
　　files=40

　　两个文件建好之后，复制到WINDOWS的system32目录下，应该可以解决问题。